Complete the following steps to customize LAN Ports, Cellular Options, Mesh Network, and Client Isolation Allowlist.
  1. From the navigation pane, click Venues.
  2. Select a venue to go to the Wi-Fi Settings page.
  3. Click Settings on upper-right corner and then select Wi-Fi Settings from the drop down.
  4. Click Networking
    The Networking page appears. By default, the LAN Ports sub-tab is displayed.
  5. Select a AP from the AP Model drop-down.
    The LAN Ports are displayed as in the the exmaple below.
    LAN Ports
  6. Select a mode from the PoE Operating Mode drop-down. By default, the PoE operating mode value is set to Auto.
    You can choose one of the following.
    • Auto
    • 802.3at
    • 802.3bt/Class 5
    • 802.3bt/Class 6
    • 802.3bt/Class 7
  7. Click the LAN port to be configured and complete the configuration.
    Depending on the AP model, up to five LAN ports can be configured. Named tabs (for example, LAN 1 and LAN 2) are displayed for each LAN port that can be configured.
    • Select the Enable Port check box.
    • Choose the Port Type. The options are Trunk, Access, or General.
    • Enter the VLAN untag ID. For a trunk port, the default is 1.
    • Enter the VLAN members. Enter a single VLAN ID or a VLAN ID range (or a combination of both). The valid VLAN ID range is 1 through 4094.
  8. Click Save Networking, and then click Close.

  1. After Step 4, select the Cellular Options sub-tab.
    The Cellular Radio Settings page appears.
  2. By default, both 1 Primary SIM and 2 Secondary SIM are set to ON. Use the toggle button to set the SIMs to ON or OFF.
    Note: You must enable at least one SIM slot (Primary or Secondary).
  3. Configure the following settings for both Primary SIM and SIM:
    • APN: Enter the APN name.
    • 3G/4G (LTE) Selection: By default, Auto is configured. You can select either 4G (LTE) only, or 3G only, or Auto.
    • Data Roaming: By deafult, data roaming is set to ON. To disable data roaming, toggel the Data Roaming to OFF.
    • LTE Band Lock: Select the bands for the 3G and 4G for your current country. Click Show band for other countries to view the available bands for other Domain 1 and Domain 2 countries, and Japan.
  4. Select the WAN Connection.
    • Ethernet (Primary) with cellular failover (Default)
    • Cellular (Primary) with Ethernet failover
    • Ethernet Only
    • Cellular Only
  5. Set the Primary WAN Recovery Timer. The default value is 60 seconds. The valid value is from 10 through 300 seconds.
  6. Click Save Networking and then click Close.

  1. After Step 4, select the Mesh Network sub-tab.
    The Mesh Network page appears.
    Mesh Network
  2. Set the Mesh Network switch to ON. By default the mesh Mesh Network is set to OFF.
    Mesh networking is enabled.
  3. Click Save Networking and then click Close.

  1. After Step 4, select the Client Isolation Allowlist sub-tab.
    The Client Isolation Allowlist dialog box appears.
    Client Isolation Allowlist
  2. Click Add Policy to add a client isolation allow-list policy.
    The create Client Isolation Allowlist Policy dialog box appears.
  3. In the Create Client Isolation Allowlist Policy dialog box, complete the following.
    Create Client Isolation Allowlist Policy
    • Policy Name: The name of the policy.
    • Description: The policy description.
    Click Add Client to add a client to the policy. You can add clients by using one of these options:
    • Select from Connected Clients: When you select this option, the Select Connected Clients dialog box appears.
      Select Connected Clients
      You can search a connected client by OS, MAC address, IP address, username, and hostname. Filter the clients by venues and/or access points.

      Select the clients that you want to add to the whitelist policy and then click Add.

    • Add New Client: When you select this option, the Create Client dialog box appears.
      Create Client

      Enter the MAC address in the MAC Address field, a description in the Description field, and then click Add.

    After adding clients to the policy, click Save in the Create Client Isolation Allowlist Policy dialog box.
  4. Click Save Networking and then click Close.